K42-MT2 x 2 pieces S42-MTA1 S42-MTA2 S42-MTA4 S42-CTA10 MT2 MT3 x 2 pieces BST5 BST9 BST11 ST42B-FMA3 1.75-20 13m/m MG _If there is a difference between the specifications and the actual product, the actual product will take precedence.

(Nikken) K42-SK16-180 NZ25-12-95 _If there is a difference between the specifications and the actual product, the actual product will take priority.

Ring outer diameter φ102, ring inner diameter φ62★

◆Chuck 6 inch three jaws◆Swing above bed: 320 ◆Swing above carriage: 160 ◆Swing above cut-off: None◆Center distance: 750-800 ◆Spindle through hole diameter: 35 ◆125-3000 rpm ◆8-point stopper_If there is a difference between the specifications and the actual product, the actual product will take precedence.

*We have many molds. If there is a difference between the specifications and the actual product, the actual product will take priority.

◆MT2 18.7 ◆MT2 22.0 ◆MT No.3 22.7 and many others_If there is a difference between the specifications and the actual product, the actual product will take priority.

[Video__ available. Check it out below! ] ◆7-inch 3-jaw hollow chuck ◆Center distance: 1000 ◆Swing above bed: 520mm ◆Rotation speed: 28-1350rpm ◆XYZ: 300×150×170 ◆Taper: MT No.5 ◆Bed width: 420 ◆Cut-off width (from face plate): 250 ◆Total bed length: 2205 ◆Spindle motor: 5.5kw 4P ◆Weight: 2570kg _If there are any differences between the specifications and the actual product, the actual product will take precedence.

◆Swing above the bed: 435mm ◆Swing between 180mm from the face plate: 490mm ◆Swing above the cross feed table: 250mm ◆Distance from floor to spindle center: 1075mm ◆Distance from bed to spindle center: 215mm ◆Maximum distance between both centers: 850mm ◆Spindle nose: JIS A-6 ◆Spindle through hole: 52mm ◆Sleeve taper: MT6 ◆Center taper: MT4 ◆Spindle speed conversion number: 12 ◆Spindle rotation speed: 32-1800min ◆Lead screw: Φ31.75 T-shaped screw 4 teeth/inch or 6mm ◆Inch screw: 80-4 teeth/inch ◆Millimeter screw: 0.25-7mm ◆DP screw: 112-8 ◆Module screw: 0.5-3.5 ◆Cross feed table travel distance: 255mm ◆Double tool rest travel distance: 150mm ◆Maximum tool angle (X×Y): 25×25mm ◆Tailstock shaft travel distance: 150mm ◆Center taper: MT4 ◆Bed top width: 352mm ◆Total bed length: 1880mm ◆Spindle motor: 3.7_(5L) 4P ◆Coolant pump motor: 100W 2P ◆Weight: 1800W _If there are any differences between the specifications and the actual product, the actual product will take precedence.

[KATO] ・MT3…1 piece・3…1 piece・TC2035…2 pieces [Nikken] ・KM32-12 _In the event of any discrepancies between the specifications and the actual product, the actual product will take priority.

◆KITAGAWA JN07 3-jaw chuck◆Swing above bed: 360mm ◆Swing above carriage: 210mm ◆Maximum distance between centers: 550mm ◆Total bed length: 1360mm ◆Bed width: 275mm ◆Spindle taper: MT No.5 ◆Spindle hole diameter: 35mm ◆Weight: 800kg _If there is a difference between the specifications and the actual product, the actual product will take precedence.

★